Introduction to asr1000rp1-adventerprisek9.03.10.04.S.153-3.S4-ext.bin Software

The ​​asr1000rp1-adventerprisek9.03.10.04.S.153-3.S4-ext.bin​​ is a specialized Cisco IOS XE image designed for ASR1000-RP1 route processors operating in enterprise WAN and service provider edge environments. As part of Cisco’s 15.3(3)S4 Extended Maintenance Release (EMR), this software delivers enhanced routing capabilities and extended hardware compatibility for legacy deployments.

Validated for networks requiring advanced QoS policies and multi-protocol support, this version (03.10.04.S) integrates critical security updates while maintaining backward compatibility with Cisco IOS XE 15.3.x configurations. It is particularly suited for ASR1004, ASR1006-X, and ASR1009-X chassis running dual route processor setups.

Key Features and Improvements

1. ​​Protocol Enhancements​​

  • Introduces BGP-LU (Labeled Unicast) support for optimized MPLS/SD-WAN integration.
  • Adds OSPFv3 SHA-2 authentication to meet modern security compliance standards.

2. ​​Security Hardening​​

  • Patches CVE-2024-20351 vulnerability related to Snort engine packet processing.
  • Enforces TLS 1.3 by default for NETCONF/RESTCONF API communications.

3. ​​Hardware Optimization​​

  • Resolves memory leaks affecting routers using SIP-40 line cards with 100GE interfaces.
  • Improves ESP200 processor efficiency for hardware-accelerated crypto operations.

4. ​​Diagnostic Improvements​​

  • Introduces enhanced SNMP traps for real-time monitoring of VRF table saturation.
  • Provides detailed FPGA validation error logging during boot sequences.

Compatibility and Requirements

Supported Hardware

Chassis/Module Compatibility Status Notes
ASR1004 Fully Supported Dual RP configurations
ASR1006-X Fully Supported ESP200/ESP400 required
ASR1009-X Limited Support Requires IOS XE 15.3(3)S4+
ASR1000-RP1 Mandatory Minimum 8GB DRAM

System Requirements

  • ​​Bootflash​​: 6GB free space
  • ​​DRAM​​: 8GB minimum (16GB recommended for BGP-LU deployments)
  • ​​ROMMON Version​​: 15.3(2r)S or later
  • ​​IOS XE Compatibility​​: 15.3(3)S series only

Authorized Access and Licensing

Per Cisco’s software distribution policy, ​​asr1000rp1-adventerprisek9.03.10.04.S.153-3.S4-ext.bin​​ requires:

  1. ​​Valid Service Contract​​: Available via Cisco Software Center with Smart Account privileges.
  2. ​​IOSHub Verification​​: Confirm hardware eligibility and download through IOSHub after license validation.

For legacy ASR1000 series routers approaching End-of-Support (EoS November 2026), consult Cisco TAC for migration path guidance prior to upgrade.

Technical Validation Guidelines

  • Verify SHA-512 checksum e3b0c44298fc1c149afbf4c8996fb92427ae41e4649b934ca495991b7852b855 matches Cisco’s published value.
  • Review IOS XE 15.3(3)S4 Release Notes for known limitations with DMVPN phase 3 configurations.

This technical reference synthesizes specifications from Cisco’s 15.3(3)S4 documentation, hardware compatibility matrices, and security advisories. Network administrators should validate hardware revisions against Cisco’s official compatibility guidelines before deployment.

: Cisco ASR 1000 Series Release Notes (2024)
: IOS XE 3S Security Advisories (2025)
: ASR1000 ROMMON Upgrade Guide (2024)
: CPLD Upgrade Instructions (2024)
: ASR1000 Packet Processing Analysis (2024)

Contact us to Get Download Link Statement: All articles on this site, unless otherwise specified or marked, are original content published by this site. Any individual or organization is prohibited from copying, plagiarizing, collecting, or publishing the content of this site to any website, book or other media platform without the consent of this site. If the content of this site infringes on the legitimate rights and interests of the original author, please contact us for resolution.