Introduction to asr1000rp1-advipservicesk9.02.06.01.122-33.XNF1.bin

This Cisco IOS XE software package provides advanced IP services for ASR 1000 Series routers equipped with Route Processor 1 (RP1), specifically targeting ASR1001 and ASR1002-X models operating in enterprise WAN environments. Released under Cisco’s Extended Maintenance cycle, this “_advipservicesk9” variant delivers enhanced routing protocols and security hardening for networks requiring BGP/MPLS VPN capabilities.

The software addresses multiple vulnerabilities in FPGA components while maintaining backward compatibility with ROMmon versions ≥12.2(33r)XNC0. Designed for deployments requiring FIPS 140-2 Level 1 compliance, it excludes non-essential modules to optimize memory utilization on legacy RP1 hardware.

Key Technical Enhancements & Protocol Support

1. Security Updates

  • ​​CVE-2024-203XX Series​​: Mitigates buffer overflow risks in BGP route processing (CVSS 7.8-9.1)
  • ​​ROMMON Authentication​​: Implements SHA-256 hashing for bootloader validation
  • ​​IPSec Session Resilience​​: Supports stateful ESP switchover with <1s failover latency

2. Protocol Optimization

  • ​​BGP Add-Path Implementation​​: Reduces route convergence time by 40% in multi-homed networks
  • ​​MPLS VPN Scaling​​: Supports 1,500 VRFs with 25,000 routes per instance
  • ​​QoS Hierarchical Shaping​​: Enables 10Gbps traffic prioritization on ESP10 modules

3. Hardware Performance

  • 15% memory utilization reduction for BGP-LS datasets
  • Extended SSD lifespan through optimized write cycles (1M+ P/E cycles)
  • 20Gbps IPSec throughput on ASR1002-X with ESP10 modules

Hardware Compatibility & System Requirements

Supported Platforms

Chassis Model Minimum ROMMON Required DRAM
ASR1001 12.2(33r)XNC0 4GB
ASR1002-X 15.5(3r)S1 8GB

Critical Compatibility Notes:

  • ​​Incompatible With​​:
    • RP2/RP3 processors
    • SIP-40 modules with firmware <12.2(33r)XN3
  • Requires 5GB free bootflash space
  • Mandatory FPGA version 19030215 for security compliance

Authorized Software Access

This Cisco IOS XE release is available through:

  1. ​​Cisco Software Center​​ (Valid Service Contract Required):

    • Navigate to Downloads > Routers > ASR 1000 Series > IOS XE 3.2S Releases

  2. ​​Legacy Hardware Support Program​​:

    • Available for EoL ASR1001 routers with active SMART Net contracts

  3. ​​Emergency Security Updates​​:

    • TAC-assisted downloads for networks impacted by CVE-2024-203XX vulnerabilities

For verified access, visit ​​IOSHub.net​​ to confirm entitlement status. All packages include SHA-512 checksums matching Cisco’s cryptographic standards for secure deployment.

Operational Recommendations

  1. ​​Pre-Installation Verification​​:

    • Execute show hw-module fpd to validate FPGA versions
    • Confirm bootflash integrity via verify /md5 bootflash:filename

  2. ​​Post-Upgrade Monitoring​​:

    • Track BGP memory utilization for 48 hours
    • Enable EEM scripts for critical process watchdog

This maintenance release carries Cisco PSIRT validation for enterprise production environments. Full technical specifications are documented in Cisco’s IOS XE 3.2S Release Notes and Security Advisory Portal.

Note: Always verify cryptographic hashes against Cisco’s published values before deployment. Third-party distribution must comply with Cisco’s End User License Agreement.

Compatibility data synthesized from Cisco’s technical documentation and hardware specifications

Contact us to Get Download Link Statement: All articles on this site, unless otherwise specified or marked, are original content published by this site. Any individual or organization is prohibited from copying, plagiarizing, collecting, or publishing the content of this site to any website, book or other media platform without the consent of this site. If the content of this site infringes on the legitimate rights and interests of the original author, please contact us for resolution.